IlPuntoTecnico
Hardware e Software => Connessioni ADSL/VDSL/FTTC => Topic aperto da: frankiep87 - 28 Giugno 2012, 13:04
-
Ho flashato questa immagine openwrt-AGV2+W-jffs2-128k-cfe.bin (presa da http://downloads.openwrt.org/snapshots/trunk/brcm63xx/ (http://downloads.openwrt.org/snapshots/trunk/brcm63xx/)) attraverso la seriale, il flash si conclude bene ma quando avvio la board ottengo questo errore e il sistema non si avvia:
CFE version 1.0.37-8.7 for AGPF 0007 BCM96358 (32bit,SP,BE)
Build Date: lun giu 16 10:47:46 CEST 2008 ( gpaolo@buildserver )
Copyright (C) 2000-2005 Broadcom Corporation.
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Flash info:
device_id : ............227E
meminfo.nsect:..........128
totalSize:..............1000000
num_erase_blocks:...... 1
device_size:............1000000
Parallel flash device: name MX29L128DT, id 0x227e, size 16384KB
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE: 0x80401000 - 0x80528CB0 (1211568)
Initialized Data: 0x8041E8A0 - 0x804204C0 (7200)
BSS Area: 0x804204C0 - 0x80426CB0 (26608)
Local Heap: 0x80426CB0 - 0x80526CB0 (1048576)
Stack Area: 0x80526CB0 - 0x80528CB0 (8192)
Text (code) segment: 0x80401000 - 0x8041E894 (120980)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : openrg.img
Boot delay (0-9 seconds) : 1
Board Id (0-3) : AGPF-S0
Number of MAC Addresses (1-32) : 13
Base MAC Address : 02:10:18:01:01:01
PSI Size (1-64) KBytes : 24
Main Thread Number [0|1] : 0
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Sizeof Tag Used : 256
One only valid image tag found ...
Trying to boot from FIRST image copy (0x80010000) ...
latest imageSequence found: ... 0
- Flash Kernel Address: 0xBE020100
- Tag->kernelLen: 0x0011FF00
- Flash Kernel Address: 0xBE020100
- Tag Kernel crc : 0xC66F7702 - calculated: 0xC66F7702
Decompression OK! - starting 0
Entry at 0x80010000
Distribution:
Version:
Build Date: Cjffs2-128k
Closing network.
Starting program at 0x80010000
SGP START PARTITION: 0
[ 0.000000] Linux version 3.3.8 (openwrt@builder) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Wed Jun 27 16:27:39 MDT 2012
[ 0.000000] Detected Broadcom 0x6358 CPU revision a1
[ 0.000000] CPU frequency is 300 MHz
[ 0.000000] 32MB of RAM installed
[ 0.000000] registering 40 GPIOs
[ 0.000000] gpiochip_add: registered GPIOs 0 to 39 on device: bcm63xx-gpio
[ 0.000000] board_bcm963xx: Boot address 0xbe000000
[ 0.000000] board_bcm963xx: CFE version: unknown
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[ 0.000000] board_bcm963xx: board name: AGPF-S0
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00000000 -> 0x00002000
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] Early memory PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00002000
[ 0.000000] Reserving 0MB of memory at 0MB for crashkernel
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Primary instruction cache 32kB, VIPT, 2-way, linesize 16 bytes.
[ 0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] Memory: 29020k/32768k available (2347k kernel code, 3748k reserved, 656k data, 200k init, 0k highmem)
[ 0.000000] NR_IRQS:128
[ 0.000000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.048000] NET: Registered protocol family 16
[ 0.060000] registering PCI controller with io_map_base unset
[ 0.064000] registering PCI controller with io_map_base unset
[ 0.076000] bio: create slab <bio-0> at 0
[ 0.084000] PCI host bridge to bus 0000:00
[ 0.088000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[ 0.092000] pci_bus 0000:00: root bus resource [io 0x8000000-0x8007fff]
[ 0.108000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x30001fff]
[ 0.112000] PCI host bridge to bus 0000:01
[ 0.116000] pci_bus 0000:01: root bus resource [mem 0x38000000-0x3fffffff]
[ 0.120000] pci_bus 0000:01: root bus resource [io 0x8008000-0x800ffff]
[ 0.124000] pci 0000:01:1e.0: CardBus bridge to [bus 02-05]
[ 0.128000] pci 0000:01:1e.0: bridge window [io 0x0001-0x0000]
[ 0.132000] pci 0000:01:1e.0: bridge window [io 0x0001-0x0000]
[ 0.136000] pci 0000:01:1e.0: bridge window [mem 0x00000001-0x00000000]
[ 0.140000] PCI: Enabling device 0000:01:1e.0 (0000 -> 0003)
[ 0.144000] Switching to clocksource MIPS
[ 0.156000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[ 0.184000] ssb: Found chip with id 0x4318, rev 0x02 and package 0x02
[ 0.236000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
[ 0.244000] NET: Registered protocol family 2
[ 0.248000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.256000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.264000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.272000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.280000] TCP reno registered
[ 0.280000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.288000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.296000] NET: Registered protocol family 1
[ 0.304000] audit: initializing netlink socket (disabled)
[ 0.308000] type=2000 audit(0.308:1): initialized
[ 0.316000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.320000] JFFlS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.332000] msgmni has been set to 56
[ 0.336000] io scheduler noop registered
[ 0.340000] io scheduler deadline registered (default)
[ 0.348000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[ 0.356000] console [ttyS0] enabled, bootconsole disabled
[ 0.356000] console [ttyS0] enabled, bootconsole disabled
[ 0.372000] physmap platform flash device: 02000000 at 1e000000
[ 0.380000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002101
[ 0.388000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.396000] Amd/Fujitsu Extended Query version 1.3.
[ 0.400000] number of CFI chips: 1
[ 0.404000] bcm63xxpart: CFE boot tag found with version 8 and board type AGPF-S0
[ 0.412000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[ 0.420000] bcm63xxpart: Partition 1 is kernel offset 20100 and length 11ff00
[ 0.424000] bcm63xxpart: Partition 2 is rootfs offset 140000 and length ea0000
[ 0.432000] bcm63xxpart: Partition 3 is nvram offset fe0000 and length 20000
[ 0.440000] bcm63xxpart: Partition 4 is linux offset 20000 and length fc0000
[ 0.448000] bcm63xxpart: Spare partition is offset 380004 and length c5fffc
[ 0.456000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
[ 0.460000] Creating 5 MTD partitions on "physmap-flash.0":
[ 0.468000] 0x000000000000-0x000000020000 : "CFE"
[ 0.476000] 0x000000020100-0x000000140000 : "kernel"
[ 0.480000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.496000] 0x000000140000-0x000000fe0000 : "rootfs"
[ 0.508000] mtd: partition "rootfs" set to be root filesystem
[ 0.512000] split_squashfs: no squashfs found in "physmap-flash.0"
[ 0.520000] 0x000000fe0000-0x000001000000 : "nvram"
[ 0.528000] 0x000000020000-0x000000fe0000 : "linux"
[ 0.544000] bcm63xx_enet MII bus: probed
[ 0.548000] bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1 [Broadcom BCM63XX (2)]
[ 0.564000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
[ 0.580000] TCP westwood registered
[ 0.584000] NET: Registered protocol family 17
[ 0.588000] Bridge firewalling registered
[ 0.596000] 8021q: 802.1Q VLAN Support v1.8
[ 1.120000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x220000
[ 1.128000] jffs2_build_filesystem(): unlocking the mtd device... done.
[ 1.132000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
[ 40.960000] JFFS2 notice: (1) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 40.976000] VFS: Mounted root (jffs2 filesystem) readonly on device 31:2.
[ 40.984000] Freeing unused kernel memory: 200k freed
awk: /proc/cpuinfo: No such file or directory
[ 43.132000] eth1: link forced UP - 100/full - flow control off/off
[ 43.376000] roboswitch: Probing device eth0: Failed to enable switch
[ 43.384000] roboswitch: Probing device eth1: found a 5325! It's a 5350.
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
- init -
Please press Enter to activate this console. [ 50.116000] Compat-wireless backport release: compat-wireless-2012-06-14
[ 50.124000] Backport based on wireless-testing.git master-2012-06-14
[ 50.128000] compat.git: wireless-testing.git
[ 50.328000] cfg80211: Calling CRDA to update world regulatory domain
[ 50.332000] cfg80211: World regulatory domain updated:
[ 50.340000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 50.348000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 50.356000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 50.364000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 50.372000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 50.380000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 20[ 51.228000] b43-phy0: Broadcom 4318 WLAN found (core revision 9)
[ 51.316000] Broadcom 43xx driver loaded [ Features: PNL ]
[ 51.368000] Button Hotplug driver version 0.4.1
[ 51.528000] PPP generic driver version 2.4.2
[ 51.728000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 51.964000] NET: Registered protocol family 24
[ 52.040000] nf_conntrack version 0.5.0 (456 buckets, 1824 max)
[ 52.448000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
[ 54.940000] System halted.
[ 54.940000] System halted
cosa puņ essere??? riesco ad accedere alla shell solo in failsafe mode premendo F quando dice "Press the [f] key and hit [enter] to enter failsafe mode"
Grazie in anticipo!
-
Usa la stable, che trovi qui http://downloads.openwrt.org/backfire/10.03.1/brcm63xx/