ADAM2 Revision 0.22.03
(C) Copyright 1996-2003 Texas Instruments Inc. All Rights Reserved.
(C) Copyright 2003 Telogy Networks, Inc.
Usage: setmfreq [-d] [-s sys_freq, in MHz] [cpu_freq, in MHz]
Memory optimization Complete!
Adam2_AR7RD >
Press any key to abort OS load, or wait 5 seconds for OS to boot...
Adam2_AR7RD >
Adam2_AR7RD >
Adam2_AR7RD > GO
GO: Command not Found!
Adam2_AR7RD > go
Copyright (C) 2006 Merlion-ACORP Russia Software Company.
Ported to DSL-30xT by JackTheVendicator <
[email protected] Thanks to Cris for helping me out with some problems in CFI flash writing.
Thanks to submax for the led.conf file.
Thanks to marven and jonnythealien for testing.
Launching kernel LZMA decompressor.
Kernel decompressor was successful ... launching kernel.
LINUX started...
Config serial console: ttyS0,38400
Auto Detection SANGAM chip
CPU revision is: 00018448
Primary instruction cache 16kb, linesize 16 bytes (4 ways)
Primary data cache 16kb, linesize 16 bytes (4 ways)
Number of TLB entries 16.
Linux version 2.4.17_mvl21-malta-mips_fp_le (
[email protected]) (gcc v
ersion 2.95.3 20010315 (release/MontaVista)) #11 Sat Jun 24 00:22:48 CEST 2006
Determined physical RAM map:
memory: 14000000 @ 00000000 (reserved)
memory: 00020000 @ 14000000 (ROM data)
memory: 007e0000 @ 14020000 (usable)
On node 0 totalpages: 2048
zone(0): 2048 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line:
calculating r4koff... 000b71b0(750000)
CPU frequency 150.00 MHz
Calibrating delay loop... 149.91 BogoMIPS
Freeing Adam2 reserved memory [0x14001000,0x0001f000]
Memory: 6196k/8192k available (1574k kernel code, 1996k reserved, 119k data, 60k
init)
Dentry-cache hash table entries: 1024 (order: 1, 8192 bytes)
Inode-cache hash table entries: 512 (order: 0, 4096 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 2048 (order: 1, 8192 bytes)
Checking for 'wait' instruction... unavailable.
POSIX conformance testing b
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
TI Optimizations: Allocating TI-Cached Memory Pool.
Warning: Number of buffers is not configured.Setting default to 128
Using 128 Buffers for TI-Cached Memory Pool.
DEBUG: Using Hybrid Mode.
NSP Optimizations: Succesfully allocated TI-Cached Memory Pool.
Initializing RT netlink socket
Starting kswapd
Disabling the Out Of Memory Killer
devfs: v1.7 (20011216) Richard Gooch (
[email protected])
devfs: boot_options: 0x1
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Adam2 environment variables API installed.
pty: 32 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with no serial options enabled
ttyS00 at 0xa8610e00 (irq = 15) is a 16550A
ttyS01 at 0xa8610f00 (irq = 16) is a 16550A
block: 64 slots per queue, batch=16
DEBUG: Initializing the voice port management module.
DEBUG: Initialization of the voice port management module successful..
Using the MAC with internal PHY
Cpmac driver is allocating buffer memor
Cpmac driver Enable TX complete interrupt
Default Asymmetric MTU for eth0 1500
PPP generic driver version 2.4.1
avalanche flash device: 0x400000 at 0x10000000.
Physically mapped flash:0: Found 1 x16 devices at 0x200000 in 16-bit mode
Amd/Fujitsu Extended Query Table v1.0 at 0x0040
number of CFI chips: 2
Looking for mtd device :mtd0:
Found a mtd0 image (0x90000), with size (0x160000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00090000-0x001f0000 : "mtd0"
Looking for mtd device :mtd1:
Found a mtd1 image (0x10000), with size (0x80000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00010000-0x00090000 : "mtd1"
Looking for mtd device :mtd2:
Found a mtd2 image (0x0), with size (0x10000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00000000-0x00010000 : "mtd2"
Looking for mtd device :mtd3:
Found a mtd3 image (0x1f0000), with size (0x10000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x001f0000-0x00200000 : "mtd3"
Looking for mtd device :mtd4:
Found a mtd4 image (0x10000), with size (0x1e0000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00010000-0x001f0000 : "mtd4"
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 512 bind 512)
Linux IP multicast router 0.06 plus PIM-SM
ip_conntrack version 2.1 (128 buckets, 1024 max) - 384 bytes per conntrack
ip_conntrack_pptp version 1.9 loaded
ip_nat_pptp version 1.5 loaded
ip_tables: (C) 2000-2002 Netfilter core team
ipt_account 0.1.6 : Piotr Gasid³o <
[email protected]>,
http://www.barbara.eu .org/~quaker/ipt_account/
netfilter PSD loaded - (c) astaro AG
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
Initializing the WAN Bridge.
Please set the MAC Address for the WAN Bridge.
Set the Environment variable 'HWA_3'.
MAC Address should be in the following format: xx:xx:xx:xx:xx:xx
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k freed
init started: BusyBox v1.2.1 (2006.08.10-10:24+0000) multi-call binary
init started: BusyBox v1.2.1 (2006.08.10-10:24+0000) multi-call binary
Starting pid 10, console /dev/tts/0: '/etc/init.d/rcS'
Algorithmics/MIPS FPU Emulator v1.5
Reading Standard Configuration File /etc/led.conf
Configured 11 states
Warning: loading tiatm will taint the kernel: no license
See
http://www.tux.org/lkml/#export-tainted for information about tainted modu
les
registered device TI Avalanche SAR
Sangam detected
DSP binary filesize = 362422 bytes
tn7dsl_set_modulation : Setting mode to 0x1
Texas Instruments ATM driver: version:[6.01.03.00]
Starting web interface: done.
Please press Enter to activate this console. tn7dsl_set_modulation : Setting mod
e to 0x1
Default Asymmetric MTU for br0 1500
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
br0: port 1(eth0) entering forwarding state
br0: topology change detected, propagating
Starting pid 67, console /dev/tts/0: '/bin/sh'
BusyBox v1.2.1 (2006.08.10-10:24+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
#
#
